With UDP / RTP you can send the stream to max.8 Exstreamers directly or also as broadcast or to a multicast address to all Exstreamers in your network (could be 100 or more). RAW TCP is limited to max 8 connections, with HTTP the Instreamer allos maximum 6 connections at the same time. Our favorite mode is RTP streaming (more details in our RTP guide) !! RTP is UDP based which is the best for realtime streaming with lowest latency. With this Exstreamer firmware you can use RAW UDP, RAW TCP, HTTP or RTP. URL = If you have changed the port number on the Instreamer´s “Stream to” entry to anything else than 0 or 80 (e.g to 3333) then you have to use the following URL line : For more information please check our Instreamer-Exstreamer_Howto.pdfĮxstreamer standard firmware (already discontinued !) The default Port 0 together with “Internet Radio” in the “Stream to” line would mean also port 80.ġ.
Streaming / “Stream to” = Internet Radio : 0.0.0.0 : 80īoth are default values. Note, this is only on the first “Stream to” entry available, not on the entries 2-8 !!! This opens a BRTP listen port where multiple Exstreamers can pull a stream from ! Streaming / “Stream to” = RTP : (Exstreamer´s IP): 4444 Īudio / “Bit Reservoir Mode” = kept empty It´s a dedicated streaming application with enhanced monitoring features and stream backup feature ! This firmware is downloadable from (under downloads). This firmware is a special firmware which can run on all Exstreamer platforms. Using the Exstreamer Streaming Client firmware A delay of 200 – 250 ms by using MP3 should run in the most stable LANs. In our test lab we have reached by using MP3 a lowest possible delay of 175 ms, lower delays (below 100 ms) are possible by using PCM or G.711.
#Barix extreamer to megaseg plus#
3,75 seconds plus network delay, which is almost nothing in a local LAN. A higher audio bandwidth fills the buffer faster and causes a lower delay.Ĭalculation example with a 128 kbit stream and a default buffer of 60000 byte:ġ28000 / 8 = 16000 bytes /s 60000 / 16000 = 3,75 s The delay can be from below 200 ms up to serveral seconds, depending from the used audio bandwidth (Codec, frequency/quality) in the Instreamer and the audio buffer (Start Threshold) in the Exstreamer. In the Exstreamer web setup on parameter “Start Threshold” (under Streaming) you can adjust the delay. DHCP is also possible but a fix IP has some advantages. It´s recommended to use the Exstreamer Streaming Client firmware! First you always should assign fix IP addresses to each unit.
#Barix extreamer to megaseg install#
No central servers, no software to install on computers. Paging stations and zones, authorize iDevices as your needs to expand the Hallways, platforms, parking structures - wherever you need toĪ server-less, self configuring system which is super easy to set up. Select zones, push a button and start talking - anyone can Using a stationary paging device or your iPhone / iPad over wifi: With automatic discovery and self configuration, installation Infrastructure already in place as the system backbone. No new wires - the system uses the IP network
Public Address announcements in specific zones or throughout The Barix Simple Paging Solution delivers crisp and clear Ethersound (ES-100/Spkr) support enables the devices to be used as a single channel receiver/decoder in realtime audio distribution applications which target ultra low latency for live audio. The Exstreamer P5 provides amplified audio (5W RMS) directly into an 8 Ohm speaker. The Exstreamer P5 is a Universal, Multiformat IP Audio Decoder with Amplifier, PoE powered. Each endpoint can be set up to receive an area wide page, or can be put into different zones for a more area specific page. The Exstreamer P5 for Simple Paging serves as the audio decoding endpoint for the Simple Paging solution.
0 kommentar(er)
